Great engine machine shop. Very expetianced. Old school get r done. Dropped off my 6.6 duromax…read moreheads machinest knew all about what to look for and how to handle them. Hot tank presure test, milling and no push to do what wasnt needed $300 two heads. Great value, great knowledge. Grest place. No BS, no hype just good work at a fair price. Two of the better honest shops i victorvill use him exclusively. Value and honest work.

I bought a travel trailer there a couple weeks ago and what a great and actually fun experience…read more It was enjoyable going through RV's with Francisco and Aaron. No pressure no rush.. Robert, Aaron and Francisco made it happen. I ended up with way more RV than expected. I definitely recommend this place!! The service dept is awesome also. Super helpful. You feel like you have known everyone here for years. Just like old friends Great place!! Mark & Stacey Mitchell 2026 Forrest River Cherokee 23DBH

So I took my Travel trailer in to be detailed inside and have all the seals replaced along with…read morehaving a new ac unit put in and serviced. When I picked it up Over $4500 later all the seals weren't replaced and the inside was a disaster because it was left open the whole time it was there. Also it was missing outside lights that had to be fixed before I left. Absolutely the worst service I have ever experienced. As far as ratings I give it a minus 100!!!

I had nothing but a great experience all around. They made it extremely easy to rent a trailer,…read moretold me told they needed from me on my end, and provided a better price than I could've hoped for. With pick up and drop off I think I spent less than 20 minutes total at this place, which I consider a good thing.

This is the best place in the High Desert to rent equipment in my opinion. I've rented, trailer,…read moretractors, and cement mixers from them and never had any issues. They are very friendly and get you going so you can work on your project fast. Rates are fair and I'll be using them for my future needs. Highly recommended.

Highly recommend this place Great customer service. The guys…read moreare very helpful. And they have earned my business and I will keep coming in recommending everybody, I know

terrible customer service. Guy basically didn't want to help me. Told me that since I didn't buy…read moremy welder there none of his supplies would fit. He didn't know tank sizes by name (letter), etc. Would never go back

Left my motor for repair and said that it was urgent. He agreed. After 3 days, he reported that…read morethe cost would be twice the cost of purchasing a new motor. I told him to keep the motor and I went and purchased the new one for half the price.

Ryobi warranty repair on my Sawsall completed professionally & in time promised. Good…read morecommunication, quality work & on time! Highly recommended!

The owner is the best ever. Works on a handshake. I have been there 3 times for home upholstery,…read moreand cars twice . He even redid my neighbors golf cart . Lowest prices in the HD

Dropped our boat carpet off 5 weeks ago to have another one made just like it. Gave 60.00 deposit…read moreand owner said it would be ready in 1 week. Went backing in a week, and was told it's not ready, ok no problem!! Went back in a week, not ready but he said he had it all cut and sent out for the binding, because he machine could not go through such thick carpet.....cool!!! Went back the next week and I was told it was at home but his sister would bring it in a couple hours to just come back at closing time. Went back in a couple hours and no one ever returned to the business. Went back today (WEEK 5) and the sister/secretary said the owner said to just give us our carpet and 60.00 deposit back!! WTH....ok whatever RGM Upholstery, guess it was never cut, or in a trunk, or on its way to the shop!! Just tell the truth!! It's not even boat season, I would have waited for quality work, heck it had already been a month!

I had Pettis Performance machine and install bronze lifter bore bushings in my iron eagle block…read more High quality work at a fair value. Very friendly, knowledgeable staff.

Pettis "flat out" ripped me off. They ruined my Pontiac 389 tri-power heads - stole my stainless…read moresteel valves & heavy duty springs and replaced them with inferior parts - thinking I would never check the head work. And of-course He lied about it all -until I provided proof. Then said it was a mistake and that engine would run fine with sloppy geometry - poor valve springs. They tipped some of the valves lower than the keepers. All the valves were tipped at different heights. "WAY OFF" the specs required. Not even ok for stock cam use. Didn't check the clearances "and, or" didn't know how to remove any boss material. I would've broke or bent the rockers, push rods, studs, or who knows what else. At best...It was very sloppy, sloppy work! It cost me an extra $800 in parts & labor to have them re-done correctly. It was years ago when I got ripped off & lied to, and I hear the son is the new owner and that the shop does great work now. But I will never trust that shop ever again. They never once even said "We're sorry" They never gave back the parts that they stole or even offer to replace the stolen parts. ( He had a GTO himself and I think he kept my parts for his own car) He was a liar and a crook plain & simple. They still owe me money to this day! Of course I'll never see it. Beware!

Five stars to Mayhem Metal Works for making a custom iron gate for my dad's backyard. Extremely…read morefriendly and high quality. Also went above and beyond to make the necessary adjustments to ensure the gate fits perfectly.

Eddie is an unbelievably talented welder, master communicator and goes WELL above and beyond to…read moremake sure he takes care of his customers. I had a very difficult project involving the fabrication of I-Beams for a window at my business. The structural engineer's notes were very hard to understand and there was information missing on the technical aspects of how the I-Beams would be secured. Eddie spoke with the structural engineer multiple times as well as the installer to insure everything went well. He also took several calls from me and explained everything in layman's terms. He even talked to my contractor and discovered we didn't have a long enough beam for fabrication. So he called his supplier and had them swap out the 20 foot beam for a 30 foot beam only charging me for the additional cost of the longer beam. Who does that for free?! Eddie does. And then he even called a week later to make sure I passed inspection and if there is anything else I needed. Thinking I was done I said we fortunately passed inspection and are good. Well then the city needed his welding certification so I called him and he texted me the certification while we were on the phone and took the time to read through the city requirements to make sure I wasn't missing anything else they may need. Eddie is just the best. Honest, fair price, phenomenal communicator, problem solver, and goes WAY out of his way to get the job done right. Do not look any further than Eddie at Mayhem. I would work with Eddie even if he were on the other side of the country. Yes he IS that good!!!