I dig this parts store. Try to support hem as much as I can. They know their stuff and they are a…read moregreat group of guys. They have a machine shop as well. Bonus.

This is the best auto parts store around, one time I needed an electric fuel pump for my boat…read moremotor, it was a 1955 40 horse. Nobody had parts for the mechanical fuel pump they asked me what it was for. I told them and they got a pump that would work for me. I bypassed the old mechanical one every other shop wanted to know what vehicle it went into what year making and model and said oh, we can't help you. CAP Is the best. I've been going there for decades and they always seem to have what I need or at least they know how to get it or cross reference.

The best local CAT dealer in all of Portland. Huge inventory and very nice facilities on Columbia…read moreBlvd.

I have recently purchased a used skid steer from the Perterson Cat Portland dealer. The loader…read morewasn't cheap. The track loader wasn't service properly and when I pick up up from the dealer the machine was also very dirty all over. I had a mechanic inspected the machine and we found out the following: 1. The water Separator was very dirty 2. The diesel filter was very dirty - doesn't seem was replaced. 3. The motor filters were not replaced as dirty as well 4. The throttle was dirty and couldn't lower the the RPM -- the machine as accelerated all the time. 5. One of the tracks come loose only after using it a few hours -- it took us a long time to put it back and tighten the other one. 6. There are two leaks - one was a hydraulic oil leak and the 2nd is in one of the drive motors. 7. One of the functions don't work Because there are many things that the technician at the dealer failed to do and fixed, it is taken me lots of time from work. The down time from not been able to used the machine is costing us a lot of money.

Our company was searching for a reliable machine shop and came across M&J Manufacturing. We were…read moreimmediately impressed by their professionalism and the quality of their work. We deal with very precise, complex parts, and many other shops were hesitant to take on the job after reviewing our drawings. M&J not only accepted the challenge but delivered excellent results. We highly recommend this shop.

They treated me so well! I had my 1969 Chevelle heads get worked on and it came out great! I have…read morenever had a manufacturing place do me as well as M&J did! I highly recommend them to work on any of your cars!

I own a 1960 Chevy Belair. I knew it had a burnt valve when I bought it, but it was all original…read moreand in such great shape at such a superb deal, I couldn't pass it up. We just don't find these rare cream puffs much anymore! After the head was taken off by a mechanic, he found out it had a cracked piston below that burnt valve. So, I did a ton of research, and where it used to be you could find machine shops all over the city - NOT ANY MORE! One place had a 9 month waiting list! Whoa! I finally found James, at Independent Cylinder Head. He could work on my engine in about 2 weeks! And the quoted price was really reasonable too!! Super nice and helpful on the phone, and after talking to him for a while, I find out he has tons of experience at other machine shops. He went out on his own, and is the owner of this shop. Great! I picked up my engine from the mechanics shop, loaded it into my pickup, and dropped it off for James to work on. We decided to not do a rebuild, with keeping old parts that were still good, but do a re-manufacture with all new parts. The only old parts were the block, the head, and the crank...only because it wasn't available brand new. My engine will be essentially brand new after he finishes!!! It didn't take long at all and I was over picking up my new engine! I dropped it off at my mechanic, and waited for him to get to it. Not getting into all of that wait - Phew! He finally got it done but the mechanic I had chosen, couldn't get it timed right, and wasn't patient enough to work through it! I would barely run...and I certainly couldn't drive it as it was. I was outta there. This mechanic had no affiliation with James at Independent Cylinder Head. Since he had been so helpful and kind, I called James and asked his opinion on what to do. He said he had a mechanic buddy, that he used to work with for a long time, that had his own shop. He'd call him for me and see if he could do my timing/tune up. He called back soon, and I was in to his buddies shop in 2 weeks! He had a couple of jobs ahead of me. I had my car towed to his shop. The day after I dropped it off to the new mechanic, two hours into the day, he called and said my car was all fixed and was running great and I could pick it up! WOW! James came through for me again! What a quick and good mechanic friend he had. I went to pick up my car in Milwaukie, OR and drove it home to Beaverton, OR without an issue! I was doing 60mph on Hwy 217, with my little 6 cylinder 235cu.in. without effort! It was purring like a kitten! Just like I wanted!!!! :) Little did I know, the mechanic called his friend James, after finishing my car, and told him how it was doing. Then, a day later, James called me to make sure everything had gone well with his recommended mechanic friend! That was a surprise! ... What a nice man James is to care so much about his customers to call and find out how satisfied I was with his recommended mechanic friend. I told him I was super happy with the mechanic, the speed he fixed it in, and the low cost, and how happy I was to hear from him (James). I don't care if you've called 50 machine shops across the country and found one you figure you'll use. STOP! Call James, and TAKE YOUR ENGINE TO HIM! We just don't get this type of incredible service that James supplies anymore! I would think I was back in the 1960's and he was right down my street and gave me the neighborhood friendly service or something! I highly suggest this very nice and dependable machine shop owned by James. I'm gonna be 69 years old in 2 months, and I'm telling ya, we just don't get this lucky very often anymore to find this exemplary service from shops! If anything, we hear about how so & so shop charged so much and didn't do a good job after paying that much! Not so with James! He takes me back to when incredible service was THE MOST IMPORTANT THING in doing a job for a customer. James is a one of a kind GEM!

From the owner: Additional hours available by appointment! Proud to be Portland's newest* automotive machine shop…read morespecializing in cylinder head reconditioning/rebuilding automotive/marine/farm equipment and more. Competition/Performance & Custom/Classic Cars - all welcome! Additional services include: - Cylinder Head Surfacing while you wait - Crankshaft Balancing - Rod Resizing - Cylinder Boring - Engine Block Deck Resurfacing - Flywheel Resurfacing - Brake Drum & Rotor Resurfacing *AERA Member *ASE Certified Master Machinist *30+ years of experience

Thesre guys are great! They took on a very small project that no body else would touch and knocked…read moreit out of the ballpark. Plus their prices seemed very fair for the quality of work they did.

From the owner: Fabrication Enterprises, Inc. was established in Portland, OR in 1987, and offers a full range of…read moremachine shop and welding shop services. Our services include: Machine shops CNC Milling Commercial welding In

Pristine condition! I couldn't be happier with the service I received from Dan's Cylinder Head!…read moreAlvin is skilled, professional, and efficient. He took the time to understand my needs, provided great advice, and delivered high-quality work that exceeded my expectations. The turnaround time was impressive, and the pricing was very fair for the level of craftsmanship. Highly recommend!"

Good service, nice prices on service forth every single penny Todd was very nice to me, and did his…read morejob in one day. Very happy with my choice!